| Use a hammer and nail set or an electric drill with countersink bit to join the frame pieces. |
|
| After the first sanding, check to see if any nails are now protruding, and, if so, countersink them. |
|
| To help prevent recurrence, countersink the nails and swab the holes with a water repellent. |
|
| It's helpful to first pre-drill a small hole in the wood where you want to countersink the brass screws. |
|
| Fasten the bottom of each brace with a 6-inch machine bolt and countersink the washer and nut. |
|
| Place the hinge leaf in the mortise and position the self-centering tool in the countersink recesses of the hinge. |
|
| Screws will give a firm hold though you'll need to pre-drill a hole with the 2mm drill bit and countersink the hole for a flush finish. |
|
| Use a nail set to countersink the brads, then fill the holes with wood filler. |
|
| He laid out the tools required to build a handcart: saws, hammer, screwdriver, brace, tape measure, square, plane, and countersink. |
|
| Note: Especially in thin bone it is important not to countersink too much, in order to save the upper cortical layer of the bone. |
|
| He required variations in engraving details, drill sizes, countersink depth and quantities between each batch for the respective component. |
|
| Having identified the correct position, mark it and make a countersink hole for the drilling process at this point. |
|
| The notch can be used to countersink the screws that are used for fixing the joists. |
|
| If needed, countersink holes in the platform from below to allow your supplementary platform to rest flush against the Hoverpad. |
|
| You can even countersink and cover the screws with a dab of caulk. |
|
| Use 12 or 16 HDG finishing nails and countersink them with a nail set. |
|
| When applying directly over an old floor, countersink any protruding nails and sand off any paint, wax, or varnish that might affect the adhering ability of the adhesive. |
|
| Search out any protruding nail heads and countersink them with a nailset. |
|
| After the 3.25 mm osteotomy and before the countersink is used, the widening of the implant bed is continued with the Z3-TD375 twist drill. |
|
| In the external borehole you countersink the channel bolt until it arrests in the turning bolt. |
|
|
|
| To position an overdimensioned hole correctly when drilling attachment holes into a rear construction, we recommend using a countersink. |
|
| Never countersink KDA combi sensors with integrated pressure measurement cell. |
|
| The countersink is used to shape the emergence profile in the implant bed guaranteeing perfect fitting accuracy of the implant in the implant bed. |
|
| Use the countersink bur with the same color code as the implant diameter. |
|
| Hold the drill firmly at an angle of about 45 degrees to the glass and bring the drill head down slowly until it just starts to cut the surface creating a countersink hole. |
|
| When painting new exterior construction where non-galvanized nails have been used, it is advisable to first countersink the nailhead, then caulk them with a top quality, water-based all-acrylic or siliconized acrylic caulk. |
|
| Countersinking the implant shoulder:: The CS360 countersink is used to produce an emergence profile around the cortical bone to guarantee perfect fitting accuracy of the implant in the cortical region. |
|
| Use of the countersink is not necessary to make this position possible. |
|
| Check that the wear in the under part does not affect the head of the bolt to the extent that the square part of the countersink bit appears and that the lower leg of the adapter does not get too loose. |
|
| Available lead-in configurations include blown, acid etched, or drilled countersink, or any combination. |
|
| I prefer to use the more standard 60-degree chamfers, so use a piloted countersink driven by a T-handle tap wrench. |
|
| Drill and countersink two side runners ready to screw into the flat supports. |
|
| Once you know the position of the joist, you can drill new pilot holes through the floorboard and countersink the screws, as before. |
|
| Pre-drill and countersink two holes in the center of wood as shown. |
|
| Drill using a 3mm drill bit and countersink, then, making sure all the edges are flush, screw the sides to the ends to form your box using 2in screws. |
|
| To lock the legs firmly in position, countersink three more screws into each leg through lines drawn on the outside of the frame 4 inches from each corner. |
|
| If this is the case with yours, fix the new skirtings in the same way, ensuring you punch the nail heads in, or countersink the screws if you're using them instead. |
|
| Countersink nail and screw heads that are sticking up above the surface. |
|
