| These include, wider chamfers, a small rounded wedge finial, a length of 10 inches or more, and very bold lambs tongue chamfer ends. |
|
| In spite of this unusual method of use, the tool performed well in cutting a chamfer. |
|
| The rear screw hole had to be drilled at an angle through the top chamfer, next to the side of the throat mortise. |
|
| On the Wilbur plane there is decorative fluting below the chamfer stops on the toe and heel end of the plane. |
|
| However, cutting away all the wood from the front edge of the splat to this line would have produced too sharp a chamfer. |
|
| The planks have to be drilled and riveted together side by side with a diagonal chamfer at their ends. |
|
| The lead-in chamfer in the design compensates for any misalignment during tube insertion. |
|
| Lacking a lathe, you should be able to carefully grind a chamfer on a suitable bolt. |
|
| The chamfer also protects the sealing lips from damage during the mounting process. |
|
| The windway, the chamfer, the window and the labium are also cleaned either with steel wool or with a file covered with sand paper. |
|
| Reduce the margins of the premolar for a fused-on ceramic shoulder down to the inner edge of the chamfer or shoulder preparation. |
|
| Cut the shaft close to the chamfer, and cover the end with the pronator quadratus muscle. |
|
| Insert the implant percutaneously, at right angles to the X-ray beam, until the chamfer meets the near cortex. |
|
| This cutaway appearance is called a chamfer, and it is intended as a subtle homage to the chamfered corners of the original twin towers. |
|
| But if I want to put a 37-degree chamfer on a table, I don't have to ask anyone's permission. |
|
| The bow's head is shaped with a woodcarver's knife, and its chamfer likewise. |
|
| The diameter of the upper cylinder may be reduced at the top to 400 mm when a chamfer not exceeding 30 ° from the horizontal is included. |
|
| The weld chamfer or joggled edge preparation follows using lathes or specially designed ma-chines. |
|
| Use the deburring tool that comes with the pipe cutter to chamfer the inside of the pipe. |
|
| Achieve optimal results of an exact and tissue-friendly chamfer or shoulder preparation. |
|
|
|
| The highly wear-resistant outside diameter is cylindrical, being relieved towards the side faces, or the transition takes the form of a chamfer. |
|
| It is recommended to chamfer or smooth sharp edges and corner of mounting materials wherever contact is made with the tractor frame. |
|
| The chamfer can either be added in the face cut or axial cut and is defined by the start diameter and an angle. |
|
| At each end of the bridge the rings are cut away to form a chamfer, to which are attached large compression yokes transferring loads to the abutments. |
|
| These figures are based on models which Morris designed c.1864-66 for the painting of the ceiling chamfer in the Chapel of Jesus College, Cambridge. |
|
| If you need only chase the inner chamfer on an existing crown just to make sure it is square, there are a couple of tools available. |
|
| This distance on the spigot includes the chamfer of the pipe. |
|
| In each case, the ends are machined square and there is no chamfer. |
|
| It does not matter here whether the preparation has a distinct chamfer or is a shoulder with a rounded inner edge. At the margins the cut should be circular with a uniform depth of 1.0 mm. |
|
| If there is no chamfer, follow the example of a factory-made spigot and machine a suitable chamfer using a beveling tool, hand rasp, disk cutter or router. |
|
| But this one is full of delights: the off-center half-timbering on the upper section, the irregular crenelations at the roof, the slight chamfer at the corner. |
|
| For through holes, the chamfer is ground with a cutting rake that throws the chips ahead of the tap into the core hole. |
|
| First is the automatic chamfer detection for holes. |
|
| After the nut has been tightened, make sure the rounded or chamfered end bolts, studs or screws extend at least the full round or chamfer through the nut. |
|
| The new In-Plastic system allows CNC machine users to cut and chamfer the top and bottom of both sides of plastics in one action. |
|
| Clean, degrease and, if necessary, chamfer the seam. |
|
| A tip chamfer can be added as modification of a tooth shape. |
|
| The company says when dead inserting gas services from outside the premises, it is customary to chamfer the leading edge of the PE pipe to aid speedy insertion. |
|
| This chamfer body permits drilling and chamfering in a single tool. |
|
| Twister features a ribbed structure that improves gripping quality and a chamfer at the start of the thread that makes the dowel easy to insert into the drill hole. |
|
