It is important for the termination to be precisely 50 ohms for the bridge to function properly on 50-ohm communication systems. |
|
If you use a resistor less than 100 ohms you'll know it because it will get hot. |
|
I searched the site and could not find the conversion between reciprocal ohms or mhos and siemens. |
|
The Wheatstone bridge is unsuitable for measuring very small resistances, of a few ohms or less. |
|
Figure 3 shows the display when the cable is terminated in its characteristic impedance of 50 ohms. |
|
Before I knew it, I forgot about everything else as I got lost in the world of volts, amps, and ohms. |
|
Both antennas feature linear polarization, an impedance of 50 ohms and maximum input power at 10 watts. |
|
Compatibility: Gaincard is capable of driving any speakers as long as their impedance stays over 4 ohms. |
|
What is the rating in ohms of the terminating resistor used to measure transmission level? |
|
That is why it is important to conduct the required ohms measurements at the prescribed intervals. |
|
Note: We recommend you use a hailer horn of 4 Ohms to obtain maximum 22 W audio output power. |
|
The surface resistance that can be achieved with the conductive MinatecĀ® pigments range from 103 to 109 ohms. |
|
If the combined impedance is over the 15 kilo ohms limit, you will need to re-prep the electrodes and check all connections. |
|
Ohmmeter, instrument for measuring electrical resistance, which is expressed in ohms. |
|
When using a potentiometer, the total resistance of the cable run should be less than 100 ohms. |
|
However, if the ohms go immediately to a low value near zero, the capacitor is shorted. |
|
The correct way to split T3 cables is to use what's called a power splitter, which contains a transformer to balance the impedance properly at 75 ohms on all connections. |
|
If approximately 400 ohms from white to red or yellow, replace the capacitor. |
|
Standard flexible coaxial cable is manufactured with characteristic impedance ranging from 50 to 92 ohms. |
|
Each antenna features vertical polarization, with an impedance of 50 ohms. |
|
|
As expected, the equivalent resistance of 1.43 ohms is smaller than either 2 ohms or 5 ohms. |
|
If the nominal capacity is not stated, energy density is calculated from the nominal voltage squared then multiplied by the discharge duration in hours divided by the discharge load in ohms and the mass in kilograms. |
|
Conductivity of a material is generally measured by passing a known current at constant voltage through a known volume of the material and determining resistance in ohms. |
|
If the monitor's loop-through output is connected to an additional device, the device's termination is set to 75 ohms and the monitor's termination is set to high impedance. |
|
This should be not less than 5000 ohms per volt of rated voltage. |
|
As with the Gaincard, Shigaraki Amplifier has an incredible speaker drivability that belie its 20W power rating. It can drive almost any speaker sufficiently as long as the impedance of the speaker stays over 4 ohms. |
|
What is the work done by a current of 5 Megafarads per second through a resistance of 10 Ohms? |
|
The model included sacrificial anode beds, with a ground resistance of 5 ohms, spaced 3,600 ft apart. |
|
The load resistance has been changed in the steps of 100 ohms and the corresponding variations in power factor has been obtained. |
|
With a resistance range from 100 ohms to 100 kilohms, standard off-the-shelf values are 1 kilohm, 2 kilohms, 5 kilohms, 10 kilohms, 20 kilohms and 100 kilohms. |
|
If resistance is measured in ohms, conductance is measured in mhos. |
|